How To Install A Vent In Your Roof To Ensure Proper Ventilation ?
The ventilation aspect of your roof holds quite an importance as far as the overall architecture of the home is concerned. A poorly ventilated home would lead to various associated problems such as moisture molds, leaks and make the entire setup condensed.
The ventilation aspect of your roof holds quite an importance as far as the overall architecture of the home is concerned. A poorly ventilated home would lead to various associated problems such as moisture molds, leaks and make the entire setup condensed.
To restore the normality of your roof and home, a vent needs to be inculcated in the scheme of the things. The vent in the roof would prevent the home from attaining an airtight setting.
The task doesn't necessarily call for the involvement of a professional contractor and can be handled by even a novice. With a right blend of repair tools and supplies, the job can be confined to a two-day task. Make sure that the typical repair tools such as pliers, a hand-held hammer, circular saw, pry bar etc. are at your disposal throughout the course of the project.
Ground a ladder firmly and climb up to the roof. The spread of the roof which looks appropriate for the installation of the vent is detected first. Slip the business-end of the tool under the edges of the concerned shingle and push down the other end of the tool to uproot the nails. All the adjoining shingles are detached partially in such a way that no damage is done to them.
Use a piece of chalk to mark down the area around the ridge cap such that a margin of about 7-8 inches is added on each side of the ridge. Make sure that the chalk is bright enough to notify you about the area later.
Bring in a circular saw to cut the roof from the line as marked. Make sure that the blade of the saw is set appropriately. A sharper blade would result in a possible damage to the underlying roof rafters as well. Once you have cut the setup, make way for the pry bar tool again to uproot the shingles.
Walk down to a local hardware store and purchase a new vent. It is likely that the salesperson would recommend a baffled vent to you. This is because a baffled vent is more efficient than the other types of vents. It prevents air from entering into the attic and at the same time, allows the hot air to escape out to the surroundings. Place the selected vent in position and nail it down. Envelop the vent with the shingles and apply some roofing cement on the setup to rigidify it.
Make sure that all the safety precautions are followed during the course of the project.
The ventilation aspect of your roof holds quite an importance as far as the overall architecture of the home is concerned. A poorly ventilated home would lead to various associated problems such as moisture molds, leaks and make the entire setup condensed.
To restore the normality of your roof and home, a vent needs to be inculcated in the scheme of the things. The vent in the roof would prevent the home from attaining an airtight setting.
The task doesn't necessarily call for the involvement of a professional contractor and can be handled by even a novice. With a right blend of repair tools and supplies, the job can be confined to a two-day task. Make sure that the typical repair tools such as pliers, a hand-held hammer, circular saw, pry bar etc. are at your disposal throughout the course of the project.
Ground a ladder firmly and climb up to the roof. The spread of the roof which looks appropriate for the installation of the vent is detected first. Slip the business-end of the tool under the edges of the concerned shingle and push down the other end of the tool to uproot the nails. All the adjoining shingles are detached partially in such a way that no damage is done to them.
Use a piece of chalk to mark down the area around the ridge cap such that a margin of about 7-8 inches is added on each side of the ridge. Make sure that the chalk is bright enough to notify you about the area later.
Bring in a circular saw to cut the roof from the line as marked. Make sure that the blade of the saw is set appropriately. A sharper blade would result in a possible damage to the underlying roof rafters as well. Once you have cut the setup, make way for the pry bar tool again to uproot the shingles.
Walk down to a local hardware store and purchase a new vent. It is likely that the salesperson would recommend a baffled vent to you. This is because a baffled vent is more efficient than the other types of vents. It prevents air from entering into the attic and at the same time, allows the hot air to escape out to the surroundings. Place the selected vent in position and nail it down. Envelop the vent with the shingles and apply some roofing cement on the setup to rigidify it.
Make sure that all the safety precautions are followed during the course of the project.
About the Author:
Scott Rodgers is a fine author who has been authoring on roofing contents for a long time now. His expertise and knowledge has given motivation to a host of workers, ranging from Springtown Roofers (Need one? click here!) to Poquoson Roofers (Need one? click here!).